Altusen KN2108 Manuel d'utilisateur Page 125
- Page / 141
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
109
Appendix
Troubleshooting
General Operation
Symptom Possible Cause Action
Erratic Operation System needs to be reset Press and hold the Reset switch (see
page 7) for longer than three seconds.
Mouse and/or Keyboard
not responding.
Improper mouse and/or
keyboard reset.
Unplug the cable(s) from the console
port(s), then plug it/them back in.
Sudden loss of network
connection.
Local reset of the
KN2108 / KN2116.
Close your KN2108 / KN2116 connection.
Wait approximately 30 seconds, and log in
again.
No video display on the
remote console.
The local console
resolution is set to 1600 x
1200 but remote
consoles only support
1280 x 1024.
Set the local console resolution to 1280 x
1024.
When logging in from a
browser, the following
message appears: 404
Object Not Found.
The login string was not
included when the IP
address was specified.
Make sure to include the forward slash and
correct login string when you specify the
KN2108 / KN2116's IP address. (See
Default Web Page Name, page 46.)
When I log in, the
browser generates a CA
Root certificate is not
trusted, or a Certificate
Error response.
The certificate’s name is
not found is not found on
Microsoft’s list of Trusted
Authorities.
The certificate can be trusted. See Trusted
Certificates, page 113, for details
There are two mouse
pointers after the remote
system is accessed.
This is normal. One is the
local console’s pointer;
the other is the remote
system’s mouse pointer.
You can shrink the non-functioning pointer
so that it is almost invisible. See Toggle
mouse display, page 71 for details.
The display on the
remote console is
distorted and performing
an Autosync doesn’t
resolve the problem.
Autosync is unable to
ascertain the proper
resolution.
1. Switch ports to a port with a different
resolution, then switch back.
2. If the above didn’t resolve the problem,
change the resolution and refresh rate
for the system running on the port.
Afterward, you can either run at the new
resolution, or switch back to the original
resolution.
kn2116_2006-12.book Page 109 Monday, January 29, 2007 3:24 PM
- 8/16 Port KVM Over the NET™ 1
- KN2108 / KN2116 1
- User Manual 1
- Regulatory Information 2
- User Notice 3
- Safety Instructions 4
- Rack Mounting 6
- Package Contents 7
- Contents 8
- Browser Operation 10
- The Windows Client 10
- The Java Client 11
- AP Operation 11
- Appendix 12
- About This Manual 13
- Conventions 14
- ALTUSEN Information 15
- Product Information 16
- Introduction 17
- Features 19
- System Requirements 20
- / KN2116: 21
- Components 22
- Rear View 24
- Hardware Setup 27
- Stacking and Rack Mounting 28
- Rack Mounting - Split 29
- Rack Mounting - Front 31
- Rack Mounting - Rear 33
- Single Station Installation 35
- SERIAL TERMINAL 37
- Two Stage Installation 38
- Chapter 2. Hardware Setup 39
- Hot Plugging 40
- Powering Off and Restarting 40
- Port ID Numbering 41
- Port Selection 41
- The Main Page 45
- The List Function 46
- Port Names 48
- The Log Page 50
- The Administration Page 51
- User Management 52
- (Continues on next page.) 53
- Service Configuration 55
- Log Server 56
- IP Address 57
- DNS Server 57
- RADIUS Settings 58
- CC Management Settings 60
- Security 61
- Default Web Page Name 62
- Customization 63
- I/O Modules 64
- Miscellaneous 67
- Date/Time 68
- Upgrading the Firmware 69
- Web Page Layout 73
- Web Page Buttons 74
- The Toolbar Icons 79
- Hotkey Operation Overview 80
- Auto Scanning 80
- Skip Mode 81
- Multiuser Operation 84
- Windows Client Control Panel 85
- Hotkey Setup 86
- Hotkey Actions: 87
- Video Settings 89
- Message Display Panel 93
- Compose Panel 93
- User List Panel 94
- The Java Client Control Panel 98
- Mouse Synchronization 100
- The Message Board 100
- The Button Bar 101
- Resolution 102
- Question Mark 102
- Lock Key LEDs 102
- Port Operation 103
- Hotkey Operation 103
- The Configuration Page 103
- KN2108 / KN2116 User Manual 104
- The Log File 105
- The Log Server 107
- Starting Up 108
- The Menu Bar 109
- The Log Server Main Screen 113
- The List Panel 114
- The Tick Panel 114
- The File Menu 118
- The Tools Menu 118
- Chapter 9. AP Operation 119
- Connecting 120
- Operation 121
- Administration 126
- Sun Systems 128
- Panel Array Mode 128
- Trusted Certificates 129
- Installing the Certificate 130
- Certificate Trusted 131
- Windows: 132
- Sun / Linux 133
- Specifications 134
- OSD Factory Default Settings 135
- Supported KVM Switches 135
- Administrator Login Failure 136
- Limited Warranty 137
Produits connexes et manuels pour Commutateurs KVM Altusen KN2108
(150 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.168 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels